もし私のRTX 4090/RTX 4080がブラックスクリーンの問題を抱えた場合、どうすればいいでしょうか？

 

NVIDIAはこの問題を検知して解決しており、NVIDIA GPUファームウェアの更新が必要な場合があります。更新をしない場合、UEFIモードの特定のマザーボード上でグラフィックカードが起動時にブラックスクリーンになる可能性があります。この更新は、起動時にブラックスクリーンが発生している場合にのみ適用する必要があります。

以下のリンクからNVIDIA GPU UEFIファームウェア更新ツールをダウンロードし、指示に従ってください。
https://nvidia.custhelp.com/app/answers/detail/a_id/5411/

ライティング効果を制御するためにVelocityXアプリを使用する前に、グラフィックスカードがVelocityXアプリと互換性があることを確認してください。

以下の対応リストを参照してください。

 

https://www.pny.com.tw/en/download/VelocityX-Support-Martix

The contacts' backup is intended for viewing only via the DUO LINK app.
Do not attempt to view the backup contents on a computer.

Due to device's reset timing, it is recommended that, after DUO LINK is disconnected from mobile device, that end user waits for 30 seconds before attempting to reconnect. This will allow the Lightning port to reset for further use.

Tap on the “Camera icon” on top left corner.

• Tap on “Gear icon” to access DUO LINK settings.
• Tap on “Privacy Setting”.
• Slide “USB Drive encryption” toggle to the right.
• Enter a six-digit password.
• Re-enter the same six-digit password.
• Note: Remember to turn encryption “off” before connecting PNY DUO LINK OTG to any computer.

1. Tap on Transfer Media and select the type of file to transfer.
2. Tap on Multiselect and select the files to transfer.
3. On the lower right corner, tap on Copy To.
4. Select folder destination.
5. Tap on Paste

Computer and motherboard manufacturers generally provide this information under the specifications for your model on their website. If you experience trouble finding this information on their website please call their technical support group for assistance.

No, defragging an SSD will put undue wear and tear on the drive and potentially cause premature 'death' of your SSD. Because of the way SSDs work, not only does data not become fragmented, but running a defragmentation utility will actually burn through the program/erase cycles.

SSD data is stored in NAND flash, different from traditional HDD, SSD size is much smaller, with no moving mechanical parts, when running the SSD it’s silent, SSD is also much faster than HDD.

All SSDs are compatible with SATA I or SATA II. However, the previous generation of SATA ports will not be as fast as the current generation. 

No, PNY SSDs operate with standard drivers making it easy to plug into and work on most major operating systems, such as Windows and Mac OS.

The most major of which are capacity and speed. You may could refer the  specification by SD Association (www.sdcard.org)

We do not suggest PNY flash card as bootable of Windows system or some device that can run an OS from.
Reminders, PNY is not responsible for any damage or failure of any third party equipment that used with PNY products.

We don't provide data recovery service. We suggest you try to found some free or trial version of the data recover software on the internet, or to contact the company that are specializes in the data recovery service.

We do not suggest PNY flash USB as bootable of Windows system or some device that can run an OS from.
Reminders, PNY is not responsible for any damage or failure of any third party equipment that used with PNY products.

You may try upgrade the Duo Link drive firmware, that to download from the PNY support page and follow the below steps.

1. Download and extract the compressed zip file. (unzip password : pny)
2. Right click the update tool, choose run as administrator
3. Plug DUO-LINK drive into any USB Port
4. Click update F/W when it shows Ready
5. It will show “Update complete” when done. (Do not remove the drive when in process)
6. Unplug the drive.

Note: It takes around 15-30 seconds to complete the update process. Firmware Update will only work on Windows OS.

You could download the repair tools from support page of PNY Asia website. Try to format it on your computer and follow the below steps.

1. Download and extract the compressed zip file
2. Plug USB drive into any USB port
3. Run the UFIX tools
4. Click Format or Start bottom when it detected the USB drive
5. It will show Complete or OK when done
6. Unplug the USB drive

Note: The tool will format and delete ALL data of the flash drive. PNY is NOT liable for data loss in connection with the product, regardless of the cause.

You can follow steps here

1. Right click to open the Start menu on your computer, select Device manager .
2. On the device manager, find your USB drive under the disk drives heading. Right-click the drive and select properties.
3. Select policies page, select the optimize for performance / better performance, click OK.
4. Open my computer, select format on the flash drive.
5. Choose NTFS in the file system drop-down box
6. Click the start button and wait until finished.

Windows operating system has a built-in limitation of the file size. So, if the USB file system is NTFS that could copy to one file be as large as 16TB. the FAT32 file system has a maximum one file size of 4GB. And the FAT16 file system has a maximum one file size of 2GB.

If you need to copy one file that size more them the built-in limitation. You may to choose to change the file system of the USB, and reformatting it